rcg e3 www.vishay.com vishay draloric revision: 13-feb-13 1 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fully rohs compliant, green, thick film, rectangular chip resistors features ? green resistor - does not use rohs exemptions ? stability ? r / r = 1 % for 1000 h at 70 c ? 2 mm pitch packaging option for 0603 size ? metal glaze on high quality ceramic ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 notes ? these resistors do not feature a limited lifetime when operated within the permissible limits. however, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifeti me. ? marking: see datasheet surface mount resistor marking (document number 20020). ? power rating depends on the max. temperat ure at the solder point, the component pl acement density and the substrate material. note (1) the power dissipation on the resistor generates a temperature rise against the local ambient, depe nding on the heat flow suppor t of the printed-circuit bo ard (thermal resistance). the rated di ssipation applie s only if the permitted film temperature of 155 c is n ot exceeded. standard electrical specifications model case size inch case size metric power rating p 70 w limiting element voltage u max. ac rms /dc v temperature coefficient ppm/k tolerance % resistance range ? series rcg0402 0402 rr 1005m 0.063 50 100 1 1r0 to 9r76 150r to 10m e24; e96 150 10r to 147r 200 5 1r0 to 10m e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 1.5 a rcg0603 0603 rr 1608m 0.1 75 100 1 1r0 to 10m e24; e96 200 5 e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 2.0 a rcg0805 0805 rr 2012m 0.125 150 100 1 1r0 to 10m e24; e96 200 5 e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 2.5 a rcg1206 1206 rr 3216m 0.25 200 100 1 1r0 to 10m e24; e96 200 5 e24 zero-ohm-resistor: r max. = 20 m ? , i max. = 3.5 a technical specifications parameter unit rcg0402 rcg0603 rcg0805 rcg1206 rated dissipation p 70 (1) w 0.063 0.1 0.125 0.25 operating voltage u max. ac rms /dc v 50 75 150 200 insulation voltage u ins (1 min) v 75 100 200 300 insulation resistance ? > 10 9 operating temperature range c - 55 to + 155 weight mg 0.65 2 5.5 10
rcg e3 www.vishay.com vishay draloric revision: 13-feb-13 2 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 part number and product description part number: rcg080510k0fkea model value tolerance tcr packaging rcg0402 rcg0603 rcg0805 rcg1206 r = decimal k = thousand m = million 0000 = 0 ? jumper f = 1.0 % j = 5.0 % z = jumper k = 100 ppm/k l = 150 ppm/k n = 200 ppm/k 0 = jumper ea, eb, ec, ed, ee, ei, el product description: rcg0805 100 10k 1 % ea rcg0805 100 10k 1 % ea model tcr resistance tolerance packaging rcg0402 rcg0603 rcg0805 rcg1206 100 ppm/k 150 ppm/k 200 ppm/k 10r = 10 ? 10k = 10 k ? 1m = 1 m ? 0r0 = jumper 1 % 5 % ea, eb, ec, ed, ee, ei, el packaging model code quantity carrier tape width pitch reel diameter rcg0402 ed 10 000 paper tape acc. to iec 60068-3 type i 8 mm 2 mm 180 mm/7" ee 50 000 330 mm/13" rcg0603 ei 5000 paper tape acc. to iec 60068-3 type i 8 mm 2 mm 180 mm/7" ed 10 000 180 mm/7" el 20 000 285 mm/11.25" ee 50 000 330 mm/13" ea 5000 paper tape acc. to iec 60068-3 type i 8 mm 4 mm 180 mm/7" eb 10 000 285 mm/11.25" ec 20 000 330 mm/13" rcg0805 ea 5000 paper tape acc. to iec 60068-3 type i 8 mm 4 mm 180 mm/7" eb 10 000 285 mm/11.25" ec 20 000 330 mm/13" rcg1206 ea 5000 paper tape acc. to iec 60068-3 type i 8 mm 4 mm 180 mm/7" eb 10 000 285 mm/11.25" ec 20 000 330 mm/13" r c g 0 8 0 5 1 0 k 0 f k e a
rcg e3 www.vishay.com vishay draloric revision: 13-feb-13 3 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 functional performance notes ? no exemptions (e.g. pb in glass) may be applied to any substances or application for the green category ? all concentration levels are based on homogenous materials dimensions in millimeters size dimensions solder pad dimensions reflow soldering wave soldering inch metric l w h t1 t2 a b l a b l 0402 1005 1.0 0.05 0.5 0.05 0.35 0.05 0.25 0.05 0.2 0.1 0.4 0.6 0.5 0603 1608 1.55 + 0.10 - 0.05 0.85 0.1 0.45 0.05 0.3 0.2 0.3 0.2 0.5 0.9 1.0 0.9 0.9 1.0 0805 2012 2.0 + 0.20 - 0.10 1.25 0.15 0.45 0.05 0.3 + 0.20 - 0.10 0.3 0.2 0.7 1.3 1.2 0.9 1.3 1.3 1206 3216 3.2 + 0.10 - 0.20 1.6 0.15 0.55 0.05 0.45 0.2 0.4 0.2 0.9 1.7 2.0 1.1 1.7 2.3 green requirements substances concentration limit lead (pb) < 1000 ppm mercury (hg) < 1000 ppm cadmium (cd) < 100 ppm hexavalent chronium < 1000 ppm polybrominated biphenyl (pbb) < 1000 ppm polybrominated diphenyl ether (pbde) < 1000 ppm bromine (br) < 900 ppm chlorine (cl) < 900 ppm sum of bromine and chlorine ? 1500 ppm max. antimony (sb) < 900 ppm red phosphorous < 100 ppm deratin g ambient temperature in amb fraction of rated dissipation p 70 - 50 0 50 100 150 0 50 100 70 c %
rcg e3 www.vishay.com vishay draloric revision: 13-feb-13 4 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change ( ? r ) stability for product types: stability class 2 or better rcg e3 1 ?? to 10 m ? 1 ?? to 10 m ? 4.5 - resistance - 1 % 5 % 4.7 - voltage proof u = 1.4 x u ins ; 60 s no flashove r or breakdown 4.13 - short time overload u = 2.5 x ? 2 x u max.; duration acc. to style (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.17.2 58 (td) solderability solder bath method; sn96.5ag3cu0.5 non-activated flux; (245 5) c (3 0.3) s good tinning ( ? 95 % covered) no visible damage 4.8.4.2 - temperature coefficient (20/- 55/20) c and (20/125/20) c 100 ppm/k, 150 ppm/k 200 ppm/k 4.32 21 (uu 3 ) shear (adhesion) rr 1608 and smaller: 9 n rr 2012 and larger: 45 n no visible damage 4.33 21 (uu 1 ) substrate bending depth 2 mm; 3 times no visible damage, no open circuit in bent position (0.25 % r + 0.05 ? ) 4.23 - climatic sequence: - (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.23.2 2 (ba) dry heat 125 c; 16 h 4.23.3 30 (db) damp heat, cyclic 55 c; ? 90 % rh; 24 h; 1 cycle 4.23.4 1 (aa) cold - 55 c; 2 h 4.23.5 13 (m) low air pressu re 1kpa; (25 10) c; 1h 4.23.6 30 (db) damp heat, cyclic 55 c; ? 90 % rh; 24 h; 5 cycles 4.23.7 - dc load u = 4.25.1 - endurance at 70 c u = ? u max.; 1.5 h on; 0.5 h off; 70 c; 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.18.2 58 (td) resistance to soldering heat solder bath method (260 5) c; (10 1) s (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.35 - flamability, needle flame test iec 60695-11-5; 10 s no burning after 30 s 4.24 78 (cab) damp heat, steady state (40 2) c; (93 3) % rh; 56 days (1 % r + 0.05 ? ) 4.25.3 - endurance at upper category temperature 155 c, 1000 h (1 % r + 0.05 ? ) (2 % r + 0.1 ? ) 4.40 - electrostatic discharge (human body model) iec 61340-3-1; 3 pos. + 3 neg. discharges; esd test voltage acc. to size (1 % r + 0.05 ? ) p 70 x r p 70 x r p 70 x r
rcg e3 www.vishay.com vishay draloric revision: 13-feb-13 5 document number: 20047 for technical questions, contact: thickfilmchip@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 all tests are carried out in accordance with the following specifications: ? en 60115-1, generic specification ? en 140400, sectional specification ? en 140401-802, detail specification ? iec 60068-2, environmental test procedures packaging of components is done in paper tapes according to iec 60286-3. 4.29 45 (xa) component solvent resistance isopropyl alcohol; 50 c; method 2 no visible damage 4.30 45 (xa) solvent resistance of marking isopropyl alcohol; 50 c; method 1, toothbrush marking legible, no visible damage 4.22 6 (fc) vibration, endurance by sweeping f = 10 hz to 2000 hz; x, y, z ? 1.5 mm; a ? 200 m/s 2 ; 10 sweeps per axis (0.25 % r + 0.05 ? ) (0.5 % r + 0.05 ? ) 4.37 - periodic electric overload u = ? 2 x u max.; 0.1 s on; 2.5 s off; 1000 cycles (1 % r + 0.05 ? ) 4.27 - single pulse high voltage overload, 10 s/700 s ? = 10 x ? 2 x u max.; 10 pulses (1 % r + 0.05 ? ) test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change ( ? r ) stability for product types: stability class 2 or better rcg e3 1 ?? to 10 m ? 1 ?? to 10 m ? 15 x p 70 x r p 70 x r
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: vishay: ? rcg06030000z0ea? rcg060310r0fkea? rcg0603100rfkea? rcg06031k00fkea? rcg060310k0fkea? rcg0603100kfkea? rcg06031m00fkea? rcg08050000z0ea? rcg080510r0fkea? rcg0805100rfkea? rcg08051k00fkea? rcg080510k0fkea? rcg0805100kfkea? rcg08051m00fkea? rcg12060000z0ea? rcg120610r0fkea? rcg1206100rfkea? rcg12061k00fkea? rcg120610k0fkea? rcg1206100kfkea? rcg12061m00fkea? rcg040210k0jned? rcg04020000z0ed? rcg04021k00fked? rcg04021k00jned? rcg04021k50fked? rcg04021m00fked? rcg04021m00jned? rcg04022k00fked? rcg040210k0fked? rcg04022k20jned? rcg040210r0jned? rcg0402100kfked? rcg0402100kjned? rcg040215k0fked? rcg0402100rjned? rcg04021r00jned? rcg040233k0jned? rcg04022r20jned? rcg12061k50fkea? rcg0805100rjnea? rcg0805499rfkea? rcg0402220rjned? rcg08057k50jnea? rcg080575k0jnea? rcg0805470rjnea? rcg12061k00jnea? rcg0805470kjnea? rcg12061m00jnea? rcg12061r00fkea? rcg12061r00jnea? rcg120610k0jnea? rcg0805220rjnea? rcg080515k0fkea? rcg08052k00fkea? rcg08052k20jnea? rcg08052r20jnea? rcg080520k0fkea? rcg080522k0jnea? RCG040220K0FKED? rcg0805220kjnea? rcg1206100kjnea? rcg08053k30jnea? rcg080533k0jnea? rcg08054k70jnea? rcg08054k99fkea? rcg08054r70jnea? rcg080547k0jnea? rcg080547r0jnea? rcg080522r0jnea? rcg1206470kjnea? rcg1206470rjnea? rcg120649k9fkea? rcg1206499rfkea? rcg12067k50jnea? rcg120675k0jnea? rcg120610r0jnea? rcg12064r70jnea? rcg120622r0jnea? rcg080549k9fkea? rcg1206100rjnea? rcg120615k0fkea? rcg12062k00fkea? rcg12062k20jnea? rcg12062r20jnea? rcg120647r0jnea? rcg120622k0jnea? rcg120647k0jnea? rcg1206220kjnea? rcg1206220rjnea? rcg12063k30jnea? rcg120633k0jnea? rcg12064k70jnea? rcg12064k99fkea? rcg120620k0fkea? rcg060310r0jnea? rcg06031k50fkea? rcg06031m00jnea? rcg06031r00fkea? rcg06031r00jnea
|
